{"id":1198,"date":"2012-08-24T07:29:35","date_gmt":"2012-08-24T07:29:35","guid":{"rendered":"http:\/\/elscintautomation.com\/wp\/?p=1198"},"modified":"2012-08-24T07:29:35","modified_gmt":"2012-08-24T07:29:35","slug":"video-showing-maintenance-of-vibratory-bowl-feeders","status":"publish","type":"post","link":"https:\/\/elscintautomation.com\/index.php\/2012\/08\/24\/video-showing-maintenance-of-vibratory-bowl-feeders\/","title":{"rendered":"Video showing Maintenance of Vibratory Bowl Feeders"},"content":{"rendered":"

Elscint a has uploaded a video showing the maintenance aspects as well as the installation and commissioning procedures of a vibratory bowl feeder on its website \u2013 www.elscintautomation.com. The video can be found at –\u00a0 http:\/\/elscintautomation.com\/wp\/bowlfeedervideos1.html The video covers not only the regular maintenance points with respect to a vibratory bowl feeder but also the installation procedure. A total of 20 points are covered. The various aspects covered in the video are –<\/p>\n

    \n
  1. Disconnect Supply<\/li>\n
  2. Check Fuse on the regulator box cover<\/li>\n
  3. Open the Regulator box cover<\/li>\n
  4. Check the Fuse inside the regulator box<\/li>\n
  5. Ensure all the screws by which the tooling of the bowl is fixed are tight<\/li>\n
  6. Remove the middle dome (it is fixed with 4 M6 allen csk screws<\/li>\n
  7. If there is a M16 bolt at the centre, please remove the same. It is fixed only for packing and transportation. It is not to be used during working<\/li>\n
  8. Check whether the screws fixing the bowl are fully tight (8 M6 Allen in case of Model 400 and Model 400 HD and 4 M6 Allen in case of Model 250)<\/li>\n
  9. Check whether the side covers are touching the aluminium top plate of the vibrator. There should be a small gap<\/li>\n
  10. Ensure that the bowl is fixed at the place of marking<\/li>\n
  11. Tighten all the 3 packs of springs (bottom as well as top screw)<\/li>\n
  12. Tighten all the three coils<\/li>\n
  13. Check the gap between the coil and magnet (it should be 1 mm for Model 250 and Model 400 and should be 2 mm for Model 400 HD and Model 630). For checking this, use a filler gauge.<\/li>\n
  14. In case it needs to be adjusted, loosen the screws fixing the magnet (2 x M6 Allen), adjust the gap and again tighten the screws of the magnet.<\/li>\n
  15. Check the gap between the counter weight and base plate. It should be 4 to 5 mm and should be consistent at all places. If it is less at one particular position, then the rubber grommet over there needs to be replaced.<\/li>\n
  16. Remove the bowl and clean the vibrator top plate (made of Aluminium)<\/li>\n
  17. Clean the bottom surface of the bowl by making it upside down<\/li>\n
  18. Clean the bowl with a solution like IPA<\/li>\n
  19. Fix the bowl with 4 or 8 screws depending upon the Model, ensure that they are fully tight (M6 Allen)<\/li>\n
  20. Fix the dome and fix 4 M6 Allen CSK screws and ensure that they are fully tight<\/li>\n<\/ol>\n

    For more information visit – www.elscintautomation.com or send mail to – sales@elscintautomation.com<\/a><\/p>\n","protected":false},"excerpt":{"rendered":"

    Elscint a has uploaded a video showing the maintenance aspects […]<\/p>\n","protected":false},"author":3,"featured_media":0,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[1],"tags":[33,441,442,484,573,592,686],"class_list":["post-1198","post","type-post","status-publish","format-standard","hentry","category-uncategorized","tag-afag-vibrator-problem","tag-how-to-solve-problems-of-vibratory-bowl-feeder","tag-how-to-vibratory-bowl-feeder","tag-maintenance-of-a-vibratory-bowl-feeder","tag-preventive-maintenance-procedure-of-vibratory-bowl-feeder","tag-rna-vibrator-problem","tag-syntron-vibrator-problem"],"_links":{"self":[{"href":"https:\/\/elscintautomation.com\/index.php\/wp-json\/wp\/v2\/posts\/1198","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/elscintautomation.com\/index.php\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/elscintautomation.com\/index.php\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/elscintautomation.com\/index.php\/wp-json\/wp\/v2\/users\/3"}],"replies":[{"embeddable":true,"href":"https:\/\/elscintautomation.com\/index.php\/wp-json\/wp\/v2\/comments?post=1198"}],"version-history":[{"count":0,"href":"https:\/\/elscintautomation.com\/index.php\/wp-json\/wp\/v2\/posts\/1198\/revisions"}],"wp:attachment":[{"href":"https:\/\/elscintautomation.com\/index.php\/wp-json\/wp\/v2\/media?parent=1198"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/elscintautomation.com\/index.php\/wp-json\/wp\/v2\/categories?post=1198"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/elscintautomation.com\/index.php\/wp-json\/wp\/v2\/tags?post=1198"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}